Health & Fitness Tips To Keep Your Sensor Secured| Dexcom Skin Grip G6 patches Volodymir BezditniyNovember 23, 20220126 views Some people with diabetes find it tough to talk about sensors. Despite the amazing capabilities of today’s technology, sensors can occasionally get deactivated for various reasons. Still, avoiding touching any door frames is more crucial than ever. Tips to keep your sensor in place are useful whether you use a FreeStyle Libre, Dexcom Skin Grip G6 patches in USA, or another flash or continuous glucose monitor (CGM) brand. These guidelines may apply to any device; if you have any questions regarding what can cause your sensor to detach, you should consult your physician. Table of Contents Make A Site Update PlanSkin Should Always Be CleanTimingPreparationTape It UpStay Away From The LotionAlternate Site LocationsDo You Still Have Concerns About Your Sensor? Make A Site Update Plan It is recommended that you schedule a site switch far in advance, so you can completely clean the new location. After removing your old sensor, it’s a good idea to wash the old site where it was attached and the new site where the new sensor will go to get rid of any leftover adhesive. Use soap and water to wash your hands and the area where you’ll be holding your new sensor or infusion set if you don’t have access to a shower. After washing, be sure the affected region of the skin is completely dry. Skin Should Always Be Clean It’s a piece of simple advice, yet it could not be more useful. To prevent infection, an alcoholic wipe or other antibacterial solution should be used to clean the skin before the sensor is inserted (these may be provided with the sensor). It’s important to clean the area before inserting Dexcom Skin Grip G6 patches in USA. Still, it would help if you didn’t do so until it’s completely dry. Using antibacterial wipes will enable the sensor adhesive to stick better and aid in avoiding infection. Timing Due to individual differences in skin type, some people may need additional time for the patch to dry and adhere. Keep your skin dry and avoid any activity that might cause you to sweat at that period. If you have to install a new sensor before night, wait until the warming time is through before turning it in. Avoid placing the patch where the skin may fold when you bend, where hair will grow, or near your waistline. Furthermore, you should switch locations for each sensor session. Preparation Make sure the area where you place Dexcom Skin Grip G6 patches in USA is smooth, free of debris, and dry before proceeding. Extra adhesive (such as Marisol or SkinTac) can be applied under the patch, away from the needle insertion site. Once it’s dry, you can put it away. Tape It Up Apply medical or overlay tape over the peeling patch to keep it in place. Completely covering it in the tape is a must. Some people may respond better to some cassettes than others; for example, there have been anecdotal reports from the diabetic community about the irritation that might arise from using certain records. Caution should be taken to avoid taping beneath the sensor pod since this might affect the accuracy of the measurements. Stay Away From The Lotion Avoid applying any skin oils or lotions around the site of implantation. The oils on your skin can prevent the sensor from sticking, and they can also prevent the tape from sticking to the sensor itself. Alternate Site Locations It’s important to consider moving the sensors around every so often. For instance, the sensor might be placed more covertly if you have a few upcoming strenuous activities planned. Switching around where you place the sensor might help you find the sweet spot. Some devices may also allow you to place sensors on your torso, bottom, stomach, or legs; however, this may vary by model. As indicated before, door frames are a sensor’s worst enemy. If you see that your sensor is being ripped off by the hinges, switching its position might assist prevent further damage. Do You Still Have Concerns About Your Sensor? In 2014, US researchers investigating skin and adhesive issues with CGMs wrote [1]: “Achieving satisfactory adhesion of the CGM sensor and transmitter may involve finding the right supplemental product or combination of products through trial and error.” Long-term usage and tolerance of CGM devices in young children can be greatly enhanced by optimizing adhesion and reducing skin irritation. It may take some time before you feel calm about Dexcom Skin Grip G6 patches in USA, but remember that even the most meticulous preparations might fail in the face of unforeseen circumstances. If your sensor isn’t sticking after trying these solutions, don’t hesitate to contact us at CGM Monitors for more assistance. Click here for more articles.